無線LANの設定方法を教えて下さい。

[new_Puppy3]

お世話になっております。

無線LANについては、メニュー→　ネットワーク　→　無線ネットワークに自動接続　を行うのですが、下記Messageが表示されて、接続（connect）出来ません。

****************************************************************

【autoconnect.sh　ウィンドウ】
wireless interface NOT FOUND. Please load　appriproate driver
↓
【AC_status.sh ウィンドウ】
cat /TMP/AC_IF NOT such file or directory
ping : bad adress 'google.com'

------> not connected <----------
*****************************************************************

Dual Bootを行っているWindowsXP Home Edition SP3では無線LANは繋がります。

完全初心者の質問で申し訳ありませんが、解決方法をご教示頂けます様お願いします。

[new_Puppy3]

お世話になります。

下記URLやGoogleを用いて無線LANの設定に挑戦していますが、どうしてもWireless　LAN　Cardをdevice認識しません。
http://www.puppylinux.org/manuals/puppy ... 81%AE/wlan

Windowsのdriverを移してきたりしましたが結果は同じでした。

無線LAN　Cardバスは　Corega製　CG-WLCB54GL です。

つきましては、何でも構いませんので、考えられる要因・意見をご教示下さい。

[phoo]

new_Puppy3さん
はじめまして。

＞【autoconnect.sh　ウィンドウ】
＞wireless interface NOT FOUND. Please load　appriproate driver
ドライバがロードされていませんのでNICとして認識されていないようです。
CoregaのCG-WLCB54GLはRT2500というチップが使われているようです。
私の環境(Puppy4.00.3JP)ではrt2500というドライバがありますので
それを指定してあげれば良いのでは、と思います。
もしお使いのPuppyのバージョンが低いなら、
これを機に最新にされてはいかがでしょうか。

[new_Puppy3]

phoo様

ご助言（ご意見）ありがとうございます。
私の使っているPuppy4.00もrt2500のドライバはあるのですが、それを指定してロードしても無線LANカードを認識しない（電源ランプが付かない。Linkランプも点滅しない）のです。

google等で調べた方法を幾つか試しましたが、駄目でした。

Ｄebianでの無線LANカード認識方法が下記URLにあったので、試したのですが、puppyとはコマンド形態が違うようで、実行できませんでした。

URL：　http://rt2x00.serialmonkey.com/wiki/ind ... 2500_Howto

つきましては、上記URLに記してあるコマンド群をPuppy　Linux用に変換したいと考えていますが、Puppyは独立系のLinuxらしく、結局分からずじまいでした。
つきましては、どなたか下記コマンド群をpuppy用に変換いただけないでしょうか？

# apt-get install module-assistant
# module-assistant prepare
# dpkg --install rt2500-source-*.deb
# module-assistant auto-install rt2500-source
# ifconfig -a　←これは多分このままと思いますが、念の為に確認させて下さい。
# echo rt2500 >> /etc/modules

厚かましいお願いであることは分かっておりますが、何卒宜しくお願いします。

[jake]

全く的外れかもしれませんが、Puppy400JPのrt2500はpciしか認識しない(= pcmciaは認識しない)ということはないでしょうか？というのも、私の使っているPuppy402(kernel2.6.25.4)ではrt2500というモジュールは無く、代わりにrt2500pciというのがあって、その説明は、
rt2500pci "pci: Ralink RT2500 PCI & PCMCIA Wireless LAN driver.
となっています。
一方、Puppy400JP(kernel2.6.21.7)のrt2500は
rt2500 "pci: Ralink RT2500 802.11g WLAN driver 1.1.0 CVS 2007090808
となっていると思います。

[jake]

# apt-get install module-assistant
# module-assistant prepare
# dpkg --install rt2500-source-*.deb
# module-assistant auto-install rt2500-source.....

残念ながらこれらのコマンドをPuppy用に変換する方法はわかりません。(多分、無理だと思います)
ただ、これらはrt2500をインストールするためのコマンドではないでしょうか？もしそうだとしたらPuppyにはすでにrt2500がインストールされているので、同じ名前のモジュールが複数存在するということになり、エラーとなるのではないでしょうか？

[phoo]

new_Puppy3さん
質問の際には状況を略さずより詳細に書いていただけると解決が早いと思います。

＞Windowsのdriverを移してきたりしましたが結果は同じでした。
これはndiswrapperを使われたということでしょうか。
↓こちらのスレッドには目を通されましたでしょうか。
viewtopic.php?t=435

私も同じく初心者で、あちこちで躓いております(^_^;)
一緒に頑張りましょう。

jakeさん
その線はありそうですね。
もしそうだとするとココにあるもので何とかなるかもしれません。
http://rt2x00.serialmonkey.com/wiki/ind ... 00_Project

[jake]

カードをPCに挿入した時点でPCはどういう反応(例えば、/var/log/masseges)をしているのでしょうか？以下の記事は参考になりませんか？
http://www.atmarkit.co.jp/flinux/rensai ... ccard.html

[jake]

PCカードの認識に付いてはこちらにもありました。
viewtopic.php?p=3236&highlight=#3236

[new_Puppy3]

jake様、phoo様

お世話になっております。
返信が遅れて申し訳ございません。

説明ベタな質問文に回答・意見を頂きまして本当にありがとうございます。

頂いたご意見を基に当方にて試した状況を報告させて頂きます。

【jake様】
１）＞私の使っているPuppy402(kernel2.6.25.4)ではrt2500というモジュールは無く、代わりにrt2500pci・・・
⇒日本語Puppyはversion　4003しか見つけれませんでした。本家のサイトに行ってもpuppy402というのは見つかりませんでした。
取り合えず、Puppy　Linux　4003をインストールしてみましたが、ドライバーの種類(rt2500pci "pci: Ralink RT2500 PCI & PCMCIA Wireless LAN driver)は同じでした。
Puppy402の入手法を教えて下さい。
また、的外れな事をしようと、皆様にご迷惑（コマンドの変換依頼）を掛けまして申し訳ありません。


２）＞カードをPCに挿入した時点でPCはどういう反応(例えば、/var/log/masseges)をしているのでしょうか？以下の記事は参考になりませんか？
⇒電源ONの状態でカードの抜き差しをしても全く反応（反応音など）はありません。
Message　FILEの内容が全く下記URLと異なるので、対処できませんでした。

http://www.atmarkit.co.jp/flinux/rensai ... ccard.html

以下に/var/log/massegesを記します。
****************　Message　******************************
Aug 30 18:48:04 (none) syslog.info syslogd started: BusyBox v1.8.2
Aug 30 18:48:04 (none) user.notice kernel: klogd started: BusyBox v1.8.2 (2007-11-30 09:20:42 GMT-8　)
Aug 30 18:48:04 (none) user.notice kernel: Linux version 2.6.21.7 (root@puppypc) (gcc version 4.2.2) #1 Sun Feb 24 10:22:08 GMT-8 2008
Aug 30 18:48:04 (none) user.info kernel: BIOS-provided physical RAM map:
Aug 30 18:48:04 (none) user.warn kernel: sanitize start
Aug 30 18:48:04 (none) user.warn kernel: sanitize end
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() type is E820_RAM
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() start: 0000000000100000 size: 000000002bef0000 end: 000000002bff0000 type: 1
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() type is E820_RAM
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() start: 000000002bff0000 size: 0000000000008000 end: 000000002bff8000 type: 3
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() start: 000000002bff8000 size: 0000000000008000 end: 000000002c000000 type: 4
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() start: 00000000ffee0000 size: 000000000002ffff end: 00000000fff0ffff type: 2
Aug 30 18:48:04 (none) user.warn kernel: copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
Aug 30 18:48:04 (none) user.warn kernel: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
Aug 30 18:48:04 (none) user.warn kernel: BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
Aug 30 18:48:04 (none) user.warn kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Aug 30 18:48:04 (none) user.warn kernel: BIOS-e820: 0000000000100000 - 000000002bff0000 (usable)
Aug 30 18:48:04 (none) user.warn kernel: BIOS-e820: 000000002bff0000 - 000000002bff8000 (ACPI data)
Aug 30 18:48:04 (none) user.warn kernel: BIOS-e820: 000000002bff8000 - 000000002c000000 (ACPI NVS)
Aug 30 18:48:04 (none) user.warn kernel: BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
Aug 30 18:48:04 (none) user.warn kernel: BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
Aug 30 18:48:04 (none) user.warn kernel: BIOS-e820: 00000000ffee0000 - 00000000fff0ffff (reserved)
Aug 30 18:48:04 (none) user.warn kernel: BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
Aug 30 18:48:04 (none) user.notice kernel: 0MB HIGHMEM available.
Aug 30 18:48:04 (none) user.notice kernel: 703MB LOWMEM available.
Aug 30 18:48:04 (none) user.debug kernel: Entering add_active_range(0, 0, 180208) 0 entries of 256 used
Aug 30 18:48:04 (none) user.warn kernel: Zone PFN ranges:
Aug 30 18:48:04 (none) user.warn kernel: DMA 0 -> 4096
Aug 30 18:48:04 (none) user.warn kernel: Normal 4096 -> 180208
Aug 30 18:48:04 (none) user.warn kernel: HighMem 180208 -> 180208
Aug 30 18:48:04 (none) user.warn kernel: early_node_map[1] active PFN ranges
Aug 30 18:48:04 (none) user.warn kernel: 0: 0 -> 180208
Aug 30 18:48:04 (none) user.debug kernel: On node 0 totalpages: 180208
Aug 30 18:48:04 (none) user.debug kernel: DMA zone: 32 pages used for memmap
Aug 30 18:48:04 (none) user.debug kernel: DMA zone: 0 pages reserved
Aug 30 18:48:04 (none) user.debug kernel: DMA zone: 4064 pages, LIFO batch:0
Aug 30 18:48:04 (none) user.debug kernel: Normal zone: 1375 pages used for memmap
Aug 30 18:48:04 (none) user.debug kernel: Normal zone: 174737 pages, LIFO batch:31
Aug 30 18:48:04 (none) user.debug kernel: HighMem zone: 0 pages used for memmap
Aug 30 18:48:04 (none) user.info kernel: DMI 2.3 present.
Aug 30 18:48:04 (none) user.warn kernel: Allocating PCI resources starting at 30000000 (gap: 2c000000:d2c00000)
Aug 30 18:48:04 (none) user.warn kernel: Built 1 zonelists. Total pages: 178801
Aug 30 18:48:04 (none) user.notice kernel: Kernel command line: root=/dev/hda6 ro pmedia=idehd psubdir=puppy4003 acpi=off pfix=ram
Aug 30 18:48:04 (none) user.info kernel: Enabling fast FPU save and restore... done.
Aug 30 18:48:04 (none) user.info kernel: Enabling unmasked SIMD FPU exception support... done.
Aug 30 18:48:04 (none) user.info kernel: Initializing CPU#0
Aug 30 18:48:04 (none) user.warn kernel: PID hash table entries: 4096 (order: 12, 16384 bytes)
Aug 30 18:48:04 (none) user.warn kernel: Detected 1503.424 MHz processor.
Aug 30 18:48:04 (none) user.warn kernel: Console: colour VGA+ 80x25
Aug 30 18:48:04 (none) user.warn kernel: Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Aug 30 18:48:04 (none) user.warn kernel: Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Aug 30 18:48:04 (none) user.info kernel: Memory: 708816k/720832k available (2415k kernel code, 11308k reserved, 827k data, 200k init, 0k highmem)
Aug 30 18:48:04 (none) user.warn kernel: virtual kernel memory layout:
Aug 30 18:48:04 (none) user.warn kernel: fixmap : 0xfffea000 - 0xfffff000 ( 84 kB)
Aug 30 18:48:04 (none) user.warn kernel: pkmap : 0xff800000 - 0xffc00000 (4096 kB)
Aug 30 18:48:04 (none) user.warn kernel: vmalloc : 0xec800000 - 0xff7fe000 ( 303 MB)
Aug 30 18:48:04 (none) user.warn kernel: lowmem : 0xc0000000 - 0xebff0000 ( 703 MB)
Aug 30 18:48:04 (none) user.warn kernel: .init : 0xc042e000 - 0xc0460000 ( 200 kB)
Aug 30 18:48:04 (none) user.warn kernel: .data : 0xc035bc99 - 0xc042aaf4 ( 827 kB)
Aug 30 18:48:04 (none) user.warn kernel: .text : 0xc0100000 - 0xc035bc99 (2415 kB)
Aug 30 18:48:04 (none) user.warn kernel: Checking if this processor honours the WP bit even in supervisor mode... Ok.
Aug 30 18:48:04 (none) user.warn kernel: Calibrating delay using timer specific routine.. 3009.30 BogoMIPS (lpj=6018618)
Aug 30 18:48:04 (none) user.warn kernel: Mount-cache hash table entries: 512
Aug 30 18:48:04 (none) user.debug kernel: CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000
Aug 30 18:48:04 (none) user.info kernel: CPU: Trace cache: 12K uops, L1 D cache: 8K
Aug 30 18:48:04 (none) user.info kernel: CPU: L2 cache: 256K
Aug 30 18:48:04 (none) user.debug kernel: CPU: After all inits, caps: bfebf9ff 00000000 00000000 00003080 00004400 00000000 00000000
Aug 30 18:48:04 (none) user.info kernel: Intel machine check architecture supported.
Aug 30 18:48:04 (none) user.info kernel: Intel machine check reporting enabled on CPU#0.
Aug 30 18:48:04 (none) user.info kernel: CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
Aug 30 18:48:04 (none) user.warn kernel: Compat vDSO mapped to ffffe000.
Aug 30 18:48:04 (none) user.warn kernel: CPU: Intel Mobile Intel(R) Celeron(R) CPU 1.50GHz stepping 07
Aug 30 18:48:04 (none) user.info kernel: Checking 'hlt' instruction... OK.
Aug 30 18:48:04 (none) user.info kernel: NET: Registered protocol family 16
Aug 30 18:48:04 (none) user.info kernel: EISA bus registered
Aug 30 18:48:04 (none) user.info kernel: PCI: PCI BIOS revision 2.10 entry at 0xfda41, last bus=1
Aug 30 18:48:04 (none) user.info kernel: PCI: Using configuration type 1
Aug 30 18:48:04 (none) user.warn kernel: Setting up standard PCI resources
Aug 30 18:48:04 (none) user.info kernel: ACPI: Interpreter disabled.
Aug 30 18:48:04 (none) user.info kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
Aug 30 18:48:04 (none) user.info kernel: pnp: PnP ACPI: disabled
Aug 30 18:48:04 (none) user.info kernel: PnPBIOS: Scanning system for PnP BIOS support...
Aug 30 18:48:04 (none) user.info kernel: PnPBIOS: Found PnP BIOS installation structure at 0xc00f7550
Aug 30 18:48:04 (none) user.info kernel: PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x63fb, dseg 0xf0000
Aug 30 18:48:04 (none) user.info kernel: PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
Aug 30 18:48:04 (none) user.notice kernel: SCSI subsystem initialized
Aug 30 18:48:04 (none) user.debug kernel: libata version 2.20 loaded.
Aug 30 18:48:04 (none) user.warn kernel: PCI: Probing PCI hardware
Aug 30 18:48:04 (none) user.debug kernel: PCI: Probing PCI hardware (bus 00)
Aug 30 18:48:04 (none) user.info kernel: Enabling SiS 96x SMBus.
Aug 30 18:48:04 (none) user.debug kernel: Boot video device is 0000:01:00.0
Aug 30 18:48:04 (none) user.info kernel: PCI: Using IRQ router SIS [1039/0962] at 0000:00:02.0
Aug 30 18:48:04 (none) user.debug kernel: PCI: setting IRQ 5 as level-triggered
Aug 30 18:48:04 (none) user.info kernel: PCI: Found IRQ 5 for device 0000:00:02.1
Aug 30 18:48:04 (none) user.info kernel: PCI: Sharing IRQ 5 with 0000:00:02.3
Aug 30 18:48:04 (none) user.debug kernel: PCI: setting IRQ 10 as level-triggered
Aug 30 18:48:04 (none) user.info kernel: PCI: Found IRQ 10 for device 0000:00:08.0
Aug 30 18:48:04 (none) user.info kernel: PCI: Sharing IRQ 10 with 0000:00:02.6
Aug 30 18:48:04 (none) user.info kernel: PCI: Sharing IRQ 10 with 0000:00:02.7
Aug 30 18:48:04 (none) user.info kernel: pnp: 00:01: iomem range 0x0-0x9fbff could not be reserved
Aug 30 18:48:04 (none) user.info kernel: pnp: 00:01: iomem range 0x9fc00-0x9ffff could not be reserved
Aug 30 18:48:04 (none) user.info kernel: pnp: 00:01: iomem range 0xf0000-0xfffff could not be reserved
Aug 30 18:48:04 (none) user.info kernel: pnp: 00:01: iomem range 0x100000-0x2bfeffff could not be reserved
Aug 30 18:48:04 (none) user.warn kernel: PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
Aug 30 18:48:04 (none) user.info kernel: PCI: Bridge: 0000:00:01.0
Aug 30 18:48:04 (none) user.info kernel: IO window: a000-afff
Aug 30 18:48:04 (none) user.info kernel: MEM window: dfe00000-dfefffff
Aug 30 18:48:04 (none) user.info kernel: PREFETCH window: cfc00000-dfcfffff
Aug 30 18:48:04 (none) user.warn kernel: PCI: Bus 2, cardbus bridge: 0000:00:08.0
Aug 30 18:48:04 (none) user.warn kernel: IO window: 00001000-000010ff
Aug 30 18:48:04 (none) user.warn kernel: IO window: 00001400-000014ff
Aug 30 18:48:04 (none) user.warn kernel: PREFETCH window: 30000000-33ffffff
Aug 30 18:48:04 (none) user.warn kernel: MEM window: 34000000-37ffffff
Aug 30 18:48:04 (none) user.info kernel: PCI: Found IRQ 10 for device 0000:00:08.0
Aug 30 18:48:04 (none) user.info kernel: PCI: Sharing IRQ 10 with 0000:00:02.6
Aug 30 18:48:04 (none) user.info kernel: PCI: Sharing IRQ 10 with 0000:00:02.7
Aug 30 18:48:04 (none) user.debug kernel: PCI: Setting latency timer of device 0000:00:08.0 to 64
Aug 30 18:48:04 (none) user.info kernel: NET: Registered protocol family 2
Aug 30 18:48:04 (none) user.info kernel: Time: tsc clocksource has been installed.
Aug 30 18:48:04 (none) user.warn kernel: IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
Aug 30 18:48:04 (none) user.warn kernel: TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
Aug 30 18:48:04 (none) user.warn kernel: TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
Aug 30 18:48:04 (none) user.info kernel: TCP: Hash tables configured (established 131072 bind 65536)
Aug 30 18:48:04 (none) user.info kernel: TCP reno registered
Aug 30 18:48:04 (none) user.info kernel: checking if image is initramfs... it is
Aug 30 18:48:04 (none) user.info kernel: Freeing initrd memory: 1237k freed
Aug 30 18:48:04 (none) user.info kernel: NTFS driver 2.1.28 [Flags: R/W].
Aug 30 18:48:04 (none) user.info kernel: io scheduler noop registered
Aug 30 18:48:04 (none) user.info kernel: io scheduler cfq registered (default)
Aug 30 18:48:04 (none) user.info kernel: isapnp: Scanning for PnP cards...
Aug 30 18:48:04 (none) user.info kernel: isapnp: No Plug & Play device found
Aug 30 18:48:04 (none) user.info kernel: Real Time Clock Driver v1.12ac
Aug 30 18:48:04 (none) user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
Aug 30 18:48:04 (none) user.info kernel: PCI: Found IRQ 10 for device 0000:00:02.6
Aug 30 18:48:04 (none) user.info kernel: PCI: Sharing IRQ 10 with 0000:00:02.7
Aug 30 18:48:04 (none) user.info kernel: PCI: Sharing IRQ 10 with 0000:00:08.0
Aug 30 18:48:04 (none) user.warn kernel: floppy0: no floppy controllers found
Aug 30 18:48:04 (none) user.warn kernel: RAMDISK driver initialized: 16 RAM disks of 13824K size 1024 blocksize
Aug 30 18:48:04 (none) user.info kernel: loop: loaded (max 8 devices)
Aug 30 18:48:04 (none) user.info kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Aug 30 18:48:04 (none) user.info kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Aug 30 18:48:04 (none) user.info kernel: SIS5513: IDE controller at PCI slot 0000:00:02.5
Aug 30 18:48:04 (none) user.info kernel: SIS5513: chipset revision 0
Aug 30 18:48:04 (none) user.info kernel: SIS5513: not 100% native mode: will probe irqs later
Aug 30 18:48:04 (none) user.info kernel: SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
Aug 30 18:48:04 (none) user.info kernel: ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
Aug 30 18:48:04 (none) user.info kernel: ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
Aug 30 18:48:04 (none) user.debug kernel: Probing IDE interface ide0...
Aug 30 18:48:04 (none) user.warn kernel: hda: IC25N040ATCS04-0, ATA DISK drive
Aug 30 18:48:04 (none) user.warn kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Aug 30 18:48:04 (none) user.debug kernel: Probing IDE interface ide1...
Aug 30 18:48:04 (none) user.warn kernel: hdc: UJDA740 DVD/CDRW, ATAPI CD/DVD-ROM drive
Aug 30 18:48:04 (none) user.warn kernel: ide1 at 0x170-0x177,0x376 on irq 15
Aug 30 18:48:04 (none) user.info kernel: hda: max request size: 128KiB
Aug 30 18:48:04 (none) user.info kernel: hda: 78140160 sectors (40007 MB) w/1768KiB Cache, CHS=65535/16/63, UDMA(33)
Aug 30 18:48:04 (none) user.info kernel: hda: cache flushes not supported
Aug 30 18:48:04 (none) user.info kernel: hda: hda1 hda2 < hda5 hda6 >
Aug 30 18:48:04 (none) user.info kernel: PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
Aug 30 18:48:04 (none) user.info kernel: i8042.c: Detected a
Aug 30 18:48:04 (none) user.info kernel: ctive multiplexing controller, rev 1.0.
Aug 30 18:48:04 (none) user.info kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Aug 30 18:48:04 (none) user.info kernel: serio: i8042 AUX0 port at 0x60,0x64 irq 12
Aug 30 18:48:04 (none) user.info kernel: serio: i8042 AUX1 port at 0x60,0x64 irq 12
Aug 30 18:48:04 (none) user.info kernel: serio: i8042 AUX2 port at 0x60,0x64 irq 12
Aug 30 18:48:04 (none) user.info kernel: serio: i8042 AUX3 port at 0x60,0x64 irq 12
Aug 30 18:48:04 (none) user.info kernel: mice: PS/2 mouse device common for all mice
Aug 30 18:48:04 (none) user.info kernel: TCP cubic registered
Aug 30 18:48:04 (none) user.info kernel: NET: Registered protocol family 1
Aug 30 18:48:04 (none) user.info kernel: NET: Registered protocol family 17
Aug 30 18:48:04 (none) user.warn kernel: Using IPI Shortcut mode
Aug 30 18:48:04 (none) user.info kernel: Freeing unused kernel memory: 200k freed
Aug 30 18:48:04 (none) user.info kernel: squashfs: version 3.3 (2007/10/31) Phillip Lougher
Aug 30 18:48:04 (none) user.info kernel: hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Aug 30 18:48:04 (none) user.info kernel: Uniform CD-ROM driver Revision: 3.20
Aug 30 18:48:04 (none) user.info kernel: usbcore: registered new interface driver usbfs
Aug 30 18:48:04 (none) user.info kernel: usbcore: registered new interface driver hub
Aug 30 18:48:04 (none) user.info kernel: usbcore: registered new device driver usb
Aug 30 18:48:04 (none) user.info kernel: Synaptics Touchpad, model: 1, fw: 4.1, id: 0x848a1, caps: 0x0/0x0
Aug 30 18:48:04 (none) user.info kernel: input: SynPS/2 Synaptics TouchPad as /class/input/input0
Aug 30 18:48:04 (none) user.debug kernel: ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
Aug 30 18:48:04 (none) user.debug kernel: PCI: setting IRQ 11 as level-triggered
Aug 30 18:48:04 (none) user.info kernel: PCI: Found IRQ 11 for device 0000:00:03.0
Aug 30 18:48:04 (none) user.info kernel: ohci_hcd 0000:00:03.0: OHCI Host Controller
Aug 30 18:48:04 (none) user.info kernel: ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
Aug 30 18:48:04 (none) user.info kernel: ohci_hcd 0000:00:03.0: irq 11, io mem 0xdfff7000
Aug 30 18:48:04 (none) user.info kernel: usb usb1: configuration #1 chosen from 1 choice
Aug 30 18:48:04 (none) user.info kernel: hub 1-0:1.0: USB hub found
Aug 30 18:48:04 (none) user.info kernel: hub 1-0:1.0: 2 ports detected
Aug 30 18:48:04 (none) user.info kernel: PCI: Found IRQ 10 for device 0000:00:03.1
Aug 30 18:48:04 (none) user.info kernel: ohci_hcd 0000:00:03.1: OHCI Host Controller
Aug 30 18:48:04 (none) user.info kernel: ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
Aug 30 18:48:04 (none) user.info kernel: ohci_hcd 0000:00:03.1: irq 10, io mem 0xdfff8000
Aug 30 18:48:04 (none) user.info kernel: usb usb2: configuration #1 chosen from 1 choice
Aug 30 18:48:04 (none) user.info kernel: hub 2-0:1.0: USB hub found
Aug 30 18:48:04 (none) user.info kernel: hub 2-0:1.0: 2 ports detected
Aug 30 18:48:04 (none) user.info kernel: PCI: Found IRQ 10 for device 0000:00:03.2
Aug 30 18:48:04 (none) user.info kernel: ohci_hcd 0000:00:03.2: OHCI Host Controller
Aug 30 18:48:04 (none) user.info kernel: ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
Aug 30 18:48:04 (none) user.info kernel: ohci_hcd 0000:00:03.2: irq 10, io mem 0xdfff9000
Aug 30 18:48:04 (none) user.info kernel: usb usb3: configuration #1 chosen from 1 choice
Aug 30 18:48:04 (none) user.info kernel: hub 3-0:1.0: USB hub found
Aug 30 18:48:04 (none) user.info kernel: hub 3-0:1.0: 2 ports detected
Aug 30 18:48:04 (none) user.info kernel: PCI: Found IRQ 5 for device 0000:00:03.3
Aug 30 18:48:04 (none) user.info kernel: ehci_hcd 0000:00:03.3: EHCI Host Controller
Aug 30 18:48:04 (none) user.info kernel: ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
Aug 30 18:48:04 (none) user.debug kernel: PCI: cache line size of 128 is not supported by device 0000:00:03.3
Aug 30 18:48:04 (none) user.info kernel: ehci_hcd 0000:00:03.3: irq 5, io mem 0xdfffa000
Aug 30 18:48:04 (none) user.info kernel: ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
Aug 30 18:48:04 (none) user.info kernel: usb usb4: configuration #1 chosen from 1 choice
Aug 30 18:48:04 (none) user.info kernel: hub 4-0:1.0: USB hub found
Aug 30 18:48:04 (none) user.info kernel: hub 4-0:1.0: 6 ports detected
Aug 30 18:48:04 (none) user.info kernel: Initializing USB Mass Storage driver...
Aug 30 18:48:04 (none) user.info kernel: usb 4-2: new high speed USB device using ehci_hcd and address 2
Aug 30 18:48:04 (none) user.info kernel: input: ImPS/2 Generic Wheel Mouse as /class/input/input1
Aug 30 18:48:04 (none) user.info kernel: input: AT Translated Set 2 keyboard as /class/input/input2
Aug 30 18:48:04 (none) user.info kernel: usb 4-2: configuration #1 chosen from 1 choice
Aug 30 18:48:04 (none) user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Aug 30 18:48:04 (none) user.debug kernel: usb-storage: device found at 2
Aug 30 18:48:04 (none) user.debug kernel: usb-storage: waiting for device to settle before scanning
Aug 30 18:48:04 (none) user.info kernel: usbcore: registered new interface driver usb-storage
Aug 30 18:48:04 (none) user.info kernel: USB Mass Storage support registered.
Aug 30 18:48:04 (none) user.info kernel: usbcore: registered new interface driver hiddev
Aug 30 18:48:04 (none) user.info kernel: usbcore: registered new interface driver usbhid
Aug 30 18:48:04 (none) user.info kernel: drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Aug 30 18:48:04 (none) user.warn kernel: Registering unionfs 2.1.2 (for 2.6.21.7)
Aug 30 18:48:04 (none) user.warn kernel: fuse init (API version 7.8　)
Aug 30 18:48:04 (none) user.notice kernel: scsi 0:0:0:0: Direct-Access Generic USB Flash Disk 0.00 PQ: 0 ANSI: 2
Aug 30 18:48:04 (none) user.notice kernel: SCSI device sda: 31588351 512-byte hdwr sectors (16173 MB)
Aug 30 18:48:04 (none) user.notice kernel: sda: Write Protect is off
Aug 30 18:48:04 (none) user.debug kernel: sda: Mode Sense: 00 00 00 00
Aug 30 18:48:04 (none) user.err kernel: sda: assuming drive cache: write through
Aug 30 18:48:04 (none) user.notice kernel: SCSI device sda: 31588351 512-byte hdwr sectors (16173 MB)
Aug 30 18:48:04 (none) user.notice kernel: sda: Write Protect is off
Aug 30 18:48:04 (none) user.debug kernel: sda: Mode Sense: 00 00 00 00
Aug 30 18:48:04 (none) user.err kernel: sda: assuming drive cache: write through
Aug 30 18:48:04 (none) user.info kernel: sda: sda1
Aug 30 18:48:04 (none) user.notice kernel: sd 0:0:0:0: Attached scsi removable disk sda
Aug 30 18:48:04 (none) user.debug kernel: usb-storage: device scan complete
Aug 30 18:48:04 (none) user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Aug 30 18:48:04 (none) user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "nls_cp437.ko"
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "nls_iso8859-1.ko"
Aug 30 18:48:04 (none) user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "i2c-core.ko"
Aug 30 18:48:04 (none) user.info kernel: sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
Aug 30 18:48:04 (none) user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "modprobe.conf"
Aug 30 18:48:04 (none) user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Aug 30 18:48:04 (none) user.warn kernel: slamr: module license 'Smart Link Ltd.' taints kernel.
Aug 30 18:48:04 (none) user.info kernel: slamr: SmartLink AMRMO modem.
Aug 30 18:48:04 (none) user.info kernel: slamr: probe 1039:7013 SiS630 card...
Aug 30 18:48:04 (none) user.info kernel: PCI: Found IRQ 10 for device 0000:00:02.6
Aug 30 18:48:04 (none) user.info kernel: PCI: Sharing IRQ 10 with 0000:00:02.7
Aug 30 18:48:04 (none) user.info kernel: PCI: Sharing IRQ 10 with 0000:00:08.0
Aug 30 18:48:04 (none) user.warn kernel: slamr: mc97 codec is SIL22
Aug 30 18:48:04 (none) user.info kernel: slamr: slamr0 is SiS630 card.
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "snd-page-alloc.ko"
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "soundcore.ko"
Aug 30 18:48:04 (none) user.warn kernel: snd: no version for "unregister_sound_special" found: kernel tainted.
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "snd.ko"
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "snd-timer.ko"
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "snd-pcm.ko"
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "ac97_bus.ko"
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "snd-ac97-codec.ko"
Aug 30 18:48:04 (none) user.info kernel: PCI: Found IRQ 10 for device 0000:00:02.7
Aug 30 18:48:04 (none) user.info kernel: PCI: Sharing IRQ 10 with 0000:00:02.6
Aug 30 18:48:04 (none) user.info kernel: PCI: Sharing IRQ 10 with 0000:00:08.0
Aug 30 18:48:04 (none) user.info kernel: intel8x0_measure_ac97_clock: measured 55422 usecs
Aug 30 18:48:04 (none) user.info kernel: intel8x0: clocking to 48000
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "snd-intel8x0.ko"
Aug 30 18:48:04 (none) user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "mii.ko"
Aug 30 18:48:04 (none) user.info kernel: sis900.c: v1.08.10 Apr. 2 2006
Aug 30 18:48:04 (none) user.info kernel: PCI: Found IRQ 10 for device 0000:00:04.0
Aug 30 18:48:04 (none) user.info kernel: 0000:00:04.0: ICS LAN PHY transceiver found at address 1.
Aug 30 18:48:04 (none) user.info kernel: 0000:00:04.0: Using transceiver found at address 1 as default
Aug 30 18:48:04 (none) user.info kernel: eth0: SiS 900 PCI Fast Ethernet at 0xcc00, IRQ 10, 00:a0:cc:dd:3b:f1.
Aug 30 18:48:04 (none) user.info kernel: apm: BIOS not found.
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "apm.ko"
Aug 30 18:48:04 (none) user.info kernel: apm: BIOS not found.
Aug 30 18:48:04 (none) user.debug kernel: unionfs: do delay copyup of "messages"
Aug 30 18:48:04 (none) user.warn kernel: unionfs: new lower inode mtime (bindex=0, name=log)
Aug 30 18:48:06 (none) user.debug kernel: unionfs: do delay copyup of "usbcore.ko"
Aug 30 18:48:06 (none) user.info kernel: usbcore: registered new interface driver usblp
Aug 30 18:48:06 (none) user.info kernel: drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Aug 30 18:48:06 (none) user.debug kernel: unionfs: do delay copyup of "usblp.ko"
Aug 30 18:48:06 (none) user.debug kernel: unionfs: do delay copyup of "battery.ko"
Aug 30 09:48:15 (none) user.debug kernel: unionfs: do delay copyup of "snd-mixer-oss.ko"
Aug 30 09:48:15 (none) user.debug kernel: unionfs: do delay copyup of "snd-seq-device.ko"
Aug 30 09:48:15 (none) user.debug kernel: unionfs: do delay copyup of "snd-seq.ko"
Aug 30 09:48:15 (none) user.debug kernel: unionfs: do delay copyup of "snd-seq-midi-event.ko"
Aug 30 09:48:15 (none) user.debug kernel: unionfs: do delay copyup of "snd-seq-oss.ko"
Aug 30 09:48:15 (none) user.debug kernel: unionfs: do delay copyup of "snd-pcm-oss.ko"
Aug 30 09:48:15 (none) user.debug kernel: unionfs: do delay copyup of "dics.dir"
Aug 30 09:48:15 (none) user.debug kernel: unionfs: do delay copyup of "parport.ko"
Aug 30 09:48:16 (none) user.debug kernel: unionfs: do delay copyup of "parport_pc.ko"
Aug 30 09:48:16 (none) user.info kernel: lp: driver loaded but no devices found
Aug 30 09:48:16 (none) user.debug kernel: unionfs: do delay copyup of "lp.ko"
Aug 30 09:48:26 (none) auth.info login[4646]: root login on 'tty1'
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:35 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: fusermountPWQo3E
Aug 30 09:48:36 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: ld.so.preload
Aug 30 09:48:40 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: ld.so.preload
Aug 30 09:48:45 (none) user.debug kernel: unionfs: do delay copyup of "dics.dir"
Aug 30 09:48:45 (none) user.debug kernel: unionfs: do delay copyup of "usr1.ctd"
Aug 30 09:48:45 (none) user.debug kernel: unionfs: do delay copyup of "keishiki.ctd"
Aug 30 09:48:45 (none) user.debug kernel: unionfs: do delay copyup of "hojoswd.ctd"
Aug 30 09:48:45 (none) user.debug kernel: unionfs: do delay copyup of "hojomwd.ctd"
Aug 30 09:48:45 (none) user.debug kernel: unionfs: do delay copyup of "gcannaf.ctd"
Aug 30 09:48:57 (none) user.debug kernel: unionfs: do delay copyup of "appreg"
Aug 30 09:57:31 (none) user.warn kernel: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Aug 30 09:58:18 (none) user.debug kernel: unionfs: saving rdstate with cookie 2 [0.0]
Aug 30 09:58:37 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: tls
Aug 30 09:58:44 (none) daemon.notice ntfs-3g[7982]: Version 1.2412 integrated FUSE 27
Aug 30 09:58:44 (none) daemon.notice ntfs-3g[7982]: Mounted /dev/hda1 (Read-Write, label "", NTFS 3.1)
Aug 30 09:58:44 (none) daemon.notice ntfs-3g[7982]: Cmdline options: umask=0,no_def_opts
Aug 30 09:58:44 (none) daemon.notice ntfs-3g[7982]: Mount options: relatime,fsname=/dev/hda1,blkdev,blksize=4096
Aug 30 10:02:17 (none) user.info kernel: ndiswrapper version 1.46 loaded (smp=no)
Aug 30 10:02:17 (none) user.info kernel: usbcore: registered new interface driver ndiswrapper
Aug 30 10:02:17 (none) user.debug kernel: unionfs: do delay copyup of "ndiswrapper.ko"
Aug 30 10:04:32 (none) user.info kernel: usbcore: deregistering interface driver ndiswrapper
Aug 30 10:06:28 (none) daemon.notice ntfs-3g[7982]: Unmounting /dev/hda1 ()
Aug 30 10:18:12 (none) daemon.notice ntfs-3g[11961]: Version 1.2412 integrated FUSE 27
Aug 30 10:18:12 (none) daemon.notice ntfs-3g[11961]: Mounted /dev/hda1 (Read-Write, label "", NTFS 3.1)
Aug 30 10:18:12 (none) daemon.notice ntfs-3g[11961]: Cmdline options: umask=0,no_def_opts
Aug 30 10:18:12 (none) daemon.notice ntfs-3g[11961]: Mount options: relatime,fsname=/dev/hda1,blkdev,blksize=4096
Aug 30 10:18:41 (none) daemon.notice ntfs-3g[11961]: Unmounting /dev/hda1 ()
Aug 30 10:18:44 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: ld.so.preload
Aug 30 10:46:21 (none) user.debug kernel: unionfs: unhashed dentry being revalidated: gconv-modules.cache
Aug 30 11:13:22 (none) user.err kernel: FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Aug 30 11:13:22 (none) user.debug kernel: unionfs: do delay copyup of "nls_utf8.ko"
*****************************************************


【phoo様】
色々なURLをご紹介頂きましてありがとうございます。

１）viewtopic.php?t=435
⇒上記URLを参照の上、コマンドを実施した結果を以下に記します。
・lspci　⇒　全くCardを認識していないようです。
******lspci　実行後message************
00:00.0 Class 0600: 1039:0650 (rev 11)

00:01.0 Class 0604: 1039:0001

00:02.0 Class 0601: 1039:0962 (rev 04)

00:02.1 Class 0c05: 1039:0016

00:02.3 Class 0c00: 1039:7007

00:02.5 Class 0101: 1039:5513

00:02.6 Class 0703: 1039:7013 (rev a0)

00:02.7 Class 0401: 1039:7012 (rev a0)

00:03.0 Class 0c03: 1039:7001 (rev 0f)

00:03.1 Class 0c03: 1039:7001 (rev 0f)

00:03.2 Class 0c03: 1039:7001 (rev 0f)

00:03.3 Class 0c03: 1039:7002

00:04.0 Class 0200: 1039:0900 (rev 91)

00:08.0 Class 0607: 1217:6972
01:00.0 Class 0300: 1039:6325
***************************************



・iwconfig
# iwconfig
lo no wirwless extensions.
eth0 no wirelwss extensions.
#

・dmesg　実施時のMessageを下記に記します。
******dmesg　実行後message************
y_e820_map() type is E820_RAM
copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2
copy_e820_map() start: 0000000000100000 size: 000000002bef0000 end: 000000002bff0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000002bff0000 size: 0000000000008000 end: 000000002bff8000 type: 3
copy_e820_map() start: 000000002bff8000 size: 0000000000008000 end: 000000002c000000 type: 4
copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2
copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
copy_e820_map() start: 00000000ffee0000 size: 000000000002ffff end: 00000000fff0ffff type: 2
copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002bff0000 (usable)
BIOS-e820: 000000002bff0000 - 000000002bff8000 (ACPI data)
BIOS-e820: 000000002bff8000 - 000000002c000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffee0000 - 00000000fff0ffff (reserved)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
703MB LOWMEM available.
Entering add_active_range(0, 0, 180208) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 180208
HighMem 180208 -> 180208
early_node_map[1] active PFN ranges
0: 0 -> 180208
On node 0 totalpages: 180208
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 1375 pages used for memmap
Normal zone: 174737 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
Allocating PCI resources starting at 30000000 (gap: 2c000000:d2c00000)
Built 1 zonelists. Total pages: 178801
Kernel command line: root=/dev/hda6 ro pmedia=idehd psubdir=puppy4003 acpi=off pfix=ram
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1503.424 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 708816k/720832k available (2415k kernel code, 11308k reserved, 827k data, 200k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfffea000 - 0xfffff000 ( 84 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xec800000 - 0xff7fe000 ( 303 MB)
lowmem : 0xc0000000 - 0xebff0000 ( 703 MB)
.init : 0xc042e000 - 0xc0460000 ( 200 kB)
.data : 0xc035bc99 - 0xc042aaf4 ( 827 kB)
.text : 0xc0100000 - 0xc035bc99 (2415 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3009.30 BogoMIPS (lpj=6018618)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU: After all inits, caps: bfebf9ff 00000000 00000000 00003080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
Compat vDSO mapped to ffffe000.
CPU: Intel Mobile Intel(R) Celeron(R) CPU 1.50GHz stepping 07
Checking 'hlt' instruction... OK.
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfda41, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f7550
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x63fb, dseg 0xf0000
PnPBIOS: 12 nodes reported by PnP BIOS; 12 recorded by driver
SCSI subsystem initialized
libata version 2.20 loaded.
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Enabling SiS 96x SMBus.
Boot video device is 0000:01:00.0
PCI: Using IRQ router SIS [1039/0962] at 0000:00:02.0
PCI: setting IRQ 5 as level-triggered
PCI: Found IRQ 5 for device 0000:00:02.1
PCI: Sharing IRQ 5 with 0000:00:02.3
PCI: setting IRQ 10 as level-triggered
PCI: Found IRQ 10 for device 0000:00:08.0
PCI: Sharing IRQ 10 with 0000:00:02.6
PCI: Sharing IRQ 10 with 0000:00:02.7
pnp: 00:01: iomem range 0x0-0x9fbff could not be reserved
pnp: 00:01: iomem range 0x9fc00-0x9ffff could not be reserved
pnp: 00:01: iomem range 0xf0000-0xfffff could not be reserved
pnp: 00:01: iomem range 0x100000-0x2bfeffff could not be reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: a000-afff
MEM window: dfe00000-dfefffff
PREFETCH window: cfc00000-dfcfffff
PCI: Bus 2, cardbus bridge: 0000:00:08.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 30000000-33ffffff
MEM window: 34000000-37ffffff
PCI: Found IRQ 10 for device 0000:00:08.0
PCI: Sharing IRQ 10 with 0000:00:02.6
PCI: Sharing IRQ 10 with 0000:00:02.7
PCI: Setting latency timer of device 0000:00:08.0 to 64
NET: Registered protocol family 2
Time: tsc clocksource has been installed.
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 1237k freed
NTFS driver 2.1.28 [Flags: R/W].
io scheduler noop registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
PCI: Found IRQ 10 for device 0000:00:02.6
PCI: Sharing IRQ 10 with 0000:00:02.7
PCI: Sharing IRQ 10 with 0000:00:08.0
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 13824K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:02.5
SIS5513: chipset revision 0
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: IC25N040ATCS04-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: UJDA740 DVD/CDRW, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/1768KiB Cache, CHS=65535/16/63, UDMA(33)
hda: cache flushes not supported
hda: hda1 hda2 < hda5 hda6 >
PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.0.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Freeing unused kernel memory: 200k freed
squashfs: version 3.3 (2007/10/31) Phillip Lougher
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Synaptics Touchpad, model: 1, fw: 4.1, id: 0x848a1, caps: 0x0/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input0
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: setting IRQ 11 as level-triggered
PCI: Found IRQ 11 for device 0000:00:03.0
ohci_hcd 0000:00:03.0: OHCI Host Controller
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:03.0: irq 11, io mem 0xdfff7000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 10 for device 0000:00:03.1
ohci_hcd 0000:00:03.1: OHCI Host Controller
ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.1: irq 10, io mem 0xdfff8000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Found IRQ 10 for device 0000:00:03.2
ohci_hcd 0000:00:03.2: OHCI Host Controller
ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:03.2: irq 10, io mem 0xdfff9000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Found IRQ 5 for device 0000:00:03.3
ehci_hcd 0000:00:03.3: EHCI Host Controller
ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 4
PCI: cache line size of 128 is not supported by device 0000:00:03.3
ehci_hcd 0000:00:03.3: irq 5, io mem 0xdfffa000
ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
Initializing USB Mass Storage driver...
usb 4-2: new high speed USB device using ehci_hcd and address 2
input: ImPS/2 Generic Wheel Mouse as /class/input/input1
input: AT Translated Set 2 keyboard as /class/input/input2
usb 4-2: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Registering unionfs 2.1.2 (for 2.6.21.7)
fuse init (API version 7.8　)
scsi 0:0:0:0: Direct-Access Generic USB Flash Disk 0.00 PQ: 0 ANSI: 2
SCSI device sda: 31588351 512-byte hdwr sectors (16173 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 31588351 512-byte hdwr sectors (16173 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
usb-storage: device scan complete
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
unionfs: do delay copyup of "nls_cp437.ko"
unionfs: do delay copyup of "nls_iso8859-1.ko"
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
unionfs: do delay copyup of "i2c-core.ko"
sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x0c00
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
unionfs: do delay copyup of "modprobe.conf"
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
slamr: module license 'Smart Link Ltd.' taints kernel.
slamr: SmartLink AMRMO modem.
slamr: probe 1039:7013 SiS630 card...
PCI: Found IRQ 10 for device 0000:00:02.6
PCI: Sharing IRQ 10 with 0000:00:02.7
PCI: Sharing IRQ 10 with 0000:00:08.0
slamr: mc97 codec is SIL22
slamr: slamr0 is SiS630 card.
unionfs: do delay copyup of "snd-page-alloc.ko"
unionfs: do delay copyup of "soundcore.ko"
snd: no version for "unregister_sound_special" found: kernel tainted.
unionfs: do delay copyup of "snd.ko"
unionfs: do delay copyup of "snd-timer.ko"
unionfs: do delay copyup of "snd-pcm.ko"
unionfs: do delay copyup of "ac97_bus.ko"
unionfs: do delay copyup of "snd-ac97-codec.ko"
PCI: Found IRQ 10 for device 0000:00:02.7
PCI: Sharing IRQ 10 with 0000:00:02.6
PCI: Sharing IRQ 10 with 0000:00:08.0
intel8x0_measure_ac97_clock: measured 55422 usecs
intel8x0: clocking to 48000
unionfs: do delay copyup of "snd-intel8x0.ko"
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
unionfs: do delay copyup of "mii.ko"
sis900.c: v1.08.10 Apr. 2 2006
PCI: Found IRQ 10 for device 0000:00:04.0
0000:00:04.0: ICS LAN PHY transceiver found at address 1.
0000:00:04.0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0xcc00, IRQ 10, 00:a0:cc:dd:3b:f1.
apm: BIOS not found.
unionfs: do delay copyup of "apm.ko"
apm: BIOS not found.
unionfs: do delay copyup of "messages"
unionfs: new lower inode mtime (bindex=0, name=log)
unionfs: do delay copyup of "usbcore.ko"
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
unionfs: do delay copyup of "usblp.ko"
unionfs: do delay copyup of "battery.ko"
unionfs: do delay copyup of "snd-mixer-oss.ko"
unionfs: do delay copyup of "snd-seq-device.ko"
unionfs: do delay copyup of "snd-seq.ko"
unionfs: do delay copyup of "snd-seq-midi-event.ko"
unionfs: do delay copyup of "snd-seq-oss.ko"
unionfs: do delay copyup of "snd-pcm-oss.ko"
unionfs: do delay copyup of "dics.dir"
unionfs: do delay copyup of "parport.ko"
unionfs: do delay copyup of "parport_pc.ko"
lp: driver loaded but no devices found
unionfs: do delay copyup of "lp.ko"
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: fusermountPWQo3E
unionfs: unhashed dentry being revalidated: ld.so.preload
unionfs: unhashed dentry being revalidated: ld.so.preload
unionfs: do delay copyup of "dics.dir"
unionfs: do delay copyup of "usr1.ctd"
unionfs: do delay copyup of "keishiki.ctd"
unionfs: do delay copyup of "hojoswd.ctd"
unionfs: do delay copyup of "hojomwd.ctd"
unionfs: do delay copyup of "gcannaf.ctd"
unionfs: do delay copyup of "appreg"
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
unionfs: saving rdstate with cookie 2 [0.0]
unionfs: unhashed dentry being revalidated: tls
ndiswrapper version 1.46 loaded (smp=no)
usbcore: registered new interface driver ndiswrapper
unionfs: do delay copyup of "ndiswrapper.ko"
usbcore: deregistering interface driver ndiswrapper
unionfs: unhashed dentry being revalidated: ld.so.preload
unionfs: unhashed dentry being revalidated: gconv-modules.cache
********************************************************************


２）http://rt2x00.serialmonkey.com/wiki/ind ... 00_Project
⇒上記URLにて英語と格闘しましたが、device認識についての具体的な記述は無いように思いました。


３)下記URLに記されているコマンドにて、PCカードの認識を調べましたが、全く認識なしでした。

viewtopic.php?p=3236&highlight=#3236

・cardctl
# cardctl info 0
open_sock( ): No such device
#

かなりの長文となりましたが、私の知識では、これらからはヒントを得る事が出来ませんでした。

つきましては、図々しいお願いですが、これらの結果に関する皆様のご意見を頂けます様お願いします。

[phoo]

あれ？PCMCIA自体が認識されていないみたいですね。

# cardctl info 0
open_sock( ): No such device
#

私の環境では認識できないカードが入っていても
ProductID等は空白で表示されますね。

メニュー>システム>PupScan インターフェース情報で
PCIインターフェースのアイコンをクリックした結果を
張り付けてみていただけませんか。

ちなみに私の環境では以下のとおりです。

----ここから----
DESCRIPTION: Intel Corporation 82440MX Host Bridge
VENDOR: 8086 DEVICE: 7194 KERNEL MODULE: unknown

DESCRIPTION: Intel Corporation 82440MX ISA Bridge
VENDOR: 8086 DEVICE: 7198 KERNEL MODULE: unknown

DESCRIPTION: Intel Corporation 82440MX EIDE Controller
VENDOR: 8086 DEVICE: 7199 KERNEL MODULE: unknown

DESCRIPTION: Intel Corporation 82440MX USB Universal Host Controller
VENDOR: 8086 DEVICE: 719a KERNEL MODULE: uhci-hcd

DESCRIPTION: Intel Corporation 82440MX Power Management Controller
VENDOR: 8086 DEVICE: 719b KERNEL MODULE: i2c-piix4

DESCRIPTION: ESS Technology ES1969 Solo-1 Audiodrive
VENDOR: 125d DEVICE: 1969 KERNEL MODULE: snd-es1938

DESCRIPTION: Rockwell International HSF 56k Data/Fax/Voice/Spkp (w/Handset) Modem
VENDOR: 127a DEVICE: 2015 KERNEL MODULE: unknown

DESCRIPTION: Ricoh Co Ltd RL5c475
VENDOR: 1180 DEVICE: 0475 KERNEL MODULE: yenta_socket


DESCRIPTION:
VENDOR: 10c8 DEVICE: 0004 KERNEL MODULE: unknown

DESCRIPTION: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller
VENDOR: 14e4 DEVICE: 4320 KERNEL MODULE: bcm43xx
----ここまで----

ハードウェア構成が違うので当然まったく同じにはなりませんが、
赤字部分に相当するCardbusのカーネルモジュールがロードされていないのではないでしょうか？

[jake]

> Puppy 402について
本家のダウンロードサイトでテスト版として公開されていたものを暇人さんが日本語化されたものです。
フォーラムは、
viewtopic.php?t=443
暇人さん作Puppy 402日本語版は、
http://nami4.dyndns.org/p_blog/resource ... me0607.iso
で公開されています。ただ、本家ではもう公開されていないようです。現在はpuppy-4.1alpha7(Puppy 407)が最新版のようです。

もっとも、PCカード自体が認識されていないようなのでモジュールの問題ではないようですね。

[new_Puppy3]

phoo様、jake様

お世話になっております。

ご回答・ご意見を頂きましてありがとうございました。

phoo様より意見がありましたメニュー　⇒　システム　⇒　PupScan　にてPCIインターフェースアイコンをクリックした結果を以下に記します。

**********PupScan　実行結果**************
DESCRIPTION: 650/M650 Host
VENDOR: 1039 DEVICE: 0650 KERNEL MODULE: unknown

DESCRIPTION: Virtual PCI-to-PCI bridge (AGP)
VENDOR: 1039 DEVICE: 0001 KERNEL MODULE: unknown

DESCRIPTION: SiS962
VENDOR: 1039 DEVICE: 0962 KERNEL MODULE: unknown

DESCRIPTION: SiS961/2 SMBus Controller
VENDOR: 1039 DEVICE: 0016 KERNEL MODULE: i2c-sis96x

DESCRIPTION: FireWire Controller
VENDOR: 1039 DEVICE: 7007 KERNEL MODULE: unknown

DESCRIPTION: 5513
VENDOR: 1039 DEVICE: 5513 KERNEL MODULE: unknown

DESCRIPTION: AC'97 Modem Controller
VENDOR: 1039 DEVICE: 7013 KERNEL MODULE: slamr

DESCRIPTION: AC'97 Sound Controller
VENDOR: 1039 DEVICE: 7012 KERNEL MODULE: snd-intel8x0

DESCRIPTION: USB 1.0 Controller
VENDOR: 1039 DEVICE: 7001 KERNEL MODULE: ohci-hcd

DESCRIPTION: USB 1.0 Controller
VENDOR: 1039 DEVICE: 7001 KERNEL MODULE: ohci-hcd

DESCRIPTION: USB 1.0 Controller
VENDOR: 1039 DEVICE: 7001 KERNEL MODULE: ohci-hcd

DESCRIPTION: USB 2.0 Controller
VENDOR: 1039 DEVICE: 7002 KERNEL MODULE: ehci-hcd

DESCRIPTION: SiS900 PCI Fast Ethernet
VENDOR: 1039 DEVICE: 0900 KERNEL MODULE: sis900

DESCRIPTION: O2 Micro, Inc. OZ601/6912/711E0 CardBus/SmartCardBus Controller
VENDOR: 1217 DEVICE: 6972 KERNEL MODULE: unknown

DESCRIPTION: 65x/M650/740 PCI/AGP VGA Display Adapter
VENDOR: 1039 DEVICE: 6325 KERNEL MODULE: unknown

****************************************

となっております。

つきましては、おんぶにだっこの質問で申し訳ありませんが、気付き点等についてアドバイスを頂けます様お願いします。

[phoo]

new_Puppy3さん
やはりPCMCIAスロット、cardbusにKernelModuleが読み込まれていませんね。

DESCRIPTION: O2 Micro, Inc. OZ601/6912/711E0 CardBus/SmartCardBus Controller
VENDOR: 1217 DEVICE: 6972 KERNEL MODULE: unknown

私も初心者でよく分からないのですが
BootManagerでyenta_soketかi82365をロードするように
指定してみてはいかがでしょうか。
O2 Micro, Inc. OZ601/6912/711E0にどちらが対応しているかは不明
ですが、この2つがcardbus用のモジュールのようです。