近頃のノートPCはバッテリー交換はメーカーサポートに出さないと出来ないような構造となっています。Windows上では80%で充電停止、その後、あるところまで下がったら充電開始の設定が出きるのですが、Puppy上では標準では未対応なのでしばらく遠ざかっていました。
コード: 全て選択
--- TLP 1.5.0 --------------------------------------------
+++ Configured Settings:
defaults.conf L0004: TLP_ENABLE="1"
defaults.conf L0005: TLP_WARN_LEVEL="3"
defaults.conf L0006: TLP_PERSISTENT_DEFAULT="0"
defaults.conf L0007: DISK_IDLE_SECS_ON_AC="0"
defaults.conf L0008: DISK_IDLE_SECS_ON_BAT="2"
defaults.conf L0009: MAX_LOST_WORK_SECS_ON_AC="15"
defaults.conf L0010: MAX_LOST_WORK_SECS_ON_BAT="60"
defaults.conf L0011: CPU_ENERGY_PERF_POLICY_ON_AC="balance_performance"
defaults.conf L0012: CPU_ENERGY_PERF_POLICY_ON_BAT="balance_power"
defaults.conf L0013: SCHED_POWERSAVE_ON_AC="0"
defaults.conf L0014: SCHED_POWERSAVE_ON_BAT="1"
defaults.conf L0015: NMI_WATCHDOG="0"
defaults.conf L0016: DISK_DEVICES="nvme0n1 sda"
defaults.conf L0017: DISK_APM_LEVEL_ON_AC="254 254"
defaults.conf L0018: DISK_APM_LEVEL_ON_BAT="128 128"
defaults.conf L0019: DISK_APM_CLASS_DENYLIST="usb ieee1394"
defaults.conf L0020: DISK_IOSCHED="keep keep"
defaults.conf L0021: SATA_LINKPWR_ON_AC="med_power_with_dipm max_performance"
defaults.conf L0022: SATA_LINKPWR_ON_BAT="med_power_with_dipm min_power"
defaults.conf L0023: AHCI_RUNTIME_PM_ON_AC="on"
defaults.conf L0024: AHCI_RUNTIME_PM_ON_BAT="auto"
defaults.conf L0025: AHCI_RUNTIME_PM_TIMEOUT="15"
defaults.conf L0026: PCIE_ASPM_ON_AC="default"
defaults.conf L0027: PCIE_ASPM_ON_BAT="default"
defaults.conf L0028: RADEON_DPM_PERF_LEVEL_ON_AC="auto"
defaults.conf L0029: RADEON_DPM_PERF_LEVEL_ON_BAT="auto"
defaults.conf L0030: RADEON_POWER_PROFILE_ON_AC="default"
defaults.conf L0031: RADEON_POWER_PROFILE_ON_BAT="default"
defaults.conf L0032: WIFI_PWR_ON_AC="off"
defaults.conf L0033: WIFI_PWR_ON_BAT="on"
defaults.conf L0034: WOL_DISABLE="Y"
defaults.conf L0035: SOUND_POWER_SAVE_ON_AC="1"
defaults.conf L0036: SOUND_POWER_SAVE_ON_BAT="1"
defaults.conf L0037: SOUND_POWER_SAVE_CONTROLLER="Y"
defaults.conf L0038: BAY_POWEROFF_ON_AC="0"
defaults.conf L0039: BAY_POWEROFF_ON_BAT="0"
defaults.conf L0040: BAY_DEVICE="sr0"
defaults.conf L0041: RUNTIME_PM_ON_AC="on"
defaults.conf L0042: RUNTIME_PM_ON_BAT="auto"
defaults.conf L0043: RUNTIME_PM_DRIVER_DENYLIST="mei_me nouveau radeon"
defaults.conf L0044: USB_AUTOSUSPEND="1"
defaults.conf L0045: USB_EXCLUDE_AUDIO="1"
defaults.conf L0046: USB_EXCLUDE_BTUSB="0"
defaults.conf L0047: USB_EXCLUDE_PHONE="0"
defaults.conf L0048: USB_EXCLUDE_PRINTER="1"
defaults.conf L0049: USB_EXCLUDE_WWAN="0"
defaults.conf L0050: USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN="0"
defaults.conf L0051: RESTORE_DEVICE_STATE_ON_STARTUP="0"
defaults.conf L0052: RESTORE_THRESHOLDS_ON_BAT="0"
defaults.conf L0053: NATACPI_ENABLE="1"
defaults.conf L0054: TPACPI_ENABLE="1"
defaults.conf L0055: TPSMAPI_ENABLE="1"
/etc/tlp.conf L0501: START_CHARGE_THRESH_BAT0="75"
/etc/tlp.conf L0502: STOP_CHARGE_THRESH_BAT0="80"
+++ System Info
System = ASUSTeK COMPUTER INC. 1.0 ZenBook UX482EG_UX482EG
BIOS = UX482EG.315
OS Release = fossapup64 9.5
Kernel = 5.17.3kirin_2022.05.27 #1 SMP PREEMPT Fri May 27 18:51:41 JST 2022 x86_64
/proc/cmdline = BOOT_IMAGE=/vmlinuz pfix=fsck pmedia=usbflash
Init system = sysvinit
Boot mode = UEFI
+++ TLP Status
State = enabled
RDW state = not installed
Last run = 16時39分11秒, 961 sec(s) ago
Mode = AC
Power source = AC
+++ Processor
CPU model = 11th Gen Intel(R) Core(TM) i7-1165G7 @ 2.80GHz
/sys/devices/system/cpu/cpu0/cpufreq/scaling_driver = intel_pstate
/sys/devices/system/cpu/cpu0/cpufreq/scaling_governor = powersave
/sys/devices/system/cpu/cpu0/cpufreq/scaling_available_governors = performance powersave
/sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq = 400000 [kHz]
/sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq = 4700000 [kHz]
/sys/devices/system/cpu/cpu0/cpufreq/energy_performance_preference = balance_performance [HWP.EPP]
/sys/devices/system/cpu/cpu0/cpufreq/energy_performance_available_preferences = default performance balance_performance balance_power power
/sys/devices/system/cpu/cpu1..cpu7: omitted for clarity, use -v to show all
/sys/devices/system/cpu/intel_pstate/status = active
/sys/devices/system/cpu/intel_pstate/min_perf_pct = 8 [%]
/sys/devices/system/cpu/intel_pstate/max_perf_pct = 100 [%]
/sys/devices/system/cpu/intel_pstate/no_turbo = 0
/sys/devices/system/cpu/intel_pstate/hwp_dynamic_boost = 0
/sys/devices/system/cpu/intel_pstate/turbo_pct = 44 [%]
/sys/devices/system/cpu/intel_pstate/num_pstates = 44
/sys/module/workqueue/parameters/power_efficient = Y
/proc/sys/kernel/nmi_watchdog = 0
+++ Platform Profile
/sys/firmware/acpi/platform_profile = (not available)
/sys/firmware/acpi/platform_profile_choices = (not available)
+++ Temperatures
CPU temp = 47 [°C]
Fan speed (fan1) = 4100 [/min]
+++ File System
/proc/sys/vm/laptop_mode = 0
/proc/sys/vm/dirty_writeback_centisecs = 1500
/proc/sys/vm/dirty_expire_centisecs = 1500
/proc/sys/vm/dirty_ratio = 20
/proc/sys/vm/dirty_background_ratio = 10
/proc/sys/fs/xfs/xfssyncd_centisecs = 1500
+++ Disks
Devices = nvme0n1 sda
/dev/nvme0n1:
Type = NVMe
Disk ID = nvme-INTEL_SSDPEKNW010T8_BTNH04940QSY1P0B
Model = INTEL SSDPEKNW010T8
Firmware = 004C
Temp = 37 °C
Scheduler = [none] mq-deadline (multi queue)
Runtime PM:
/sys/block/nvme0n1/device/power/control = on, autosuspend_delay_ms = (not available)
/dev/sda:
Type = USB
Disk ID = usb-ELECOM_MF-CAU31_070D1AA3A5949E14-0:0
Model = ELECOM MFCAU31
Firmware = unknown
APM Level = none/disabled
Status = standby
Scheduler = [mq-deadline] none (multi queue)
Runtime PM:
/sys/block/sda/device/power/control = on, autosuspend_delay_ms = 15000
+++ Intel Graphics
/sys/class/drm/card0/device/driver = i915
/sys/class/drm/card0/power/rc6_enable = 1 (enabled)
/sys/module/i915/parameters/enable_fbc = -1 (use per-chip default)
/sys/module/i915/parameters/enable_psr = -1 (use per-chip default)
/sys/class/drm/card0/gt_min_freq_mhz = 100 [MHz]
/sys/class/drm/card0/gt_max_freq_mhz = 1300 [MHz]
/sys/class/drm/card0/gt_boost_freq_mhz = 1300 [MHz]
/sys/class/drm/card0/gt_RPn_freq_mhz = 100 [MHz] (GPU min)
/sys/class/drm/card0/gt_RP0_freq_mhz = 1300 [MHz] (GPU max)
+++ Nvidia Graphics
/sys/class/drm/card1/device/driver = nouveau
+++ Wireless
bluetooth = on
nfc = none (no device)
wifi = on
wwan = none (no device)
hci0(btusb) : bluetooth, not connected
wlan0(iwlwifi) : wifi, connected, power management = off
+++ Audio
/sys/module/snd_hda_intel/parameters/power_save = 1
/sys/module/snd_hda_intel/parameters/power_save_controller = Y
+++ PCIe Active State Power Management
/sys/module/pcie_aspm/parameters/policy = [default] performance powersave powersupersave
+++ PCIe Runtime Power Management
Enable devices = (disabled)
Disable devices = (disabled)
Device denylist = (disabled)
Driver denylist = mei_me nouveau radeon
/sys/bus/pci/devices/0000:00:00.0/power/control = on (0x060000, Host bridge, no driver)
/sys/bus/pci/devices/0000:00:02.0/power/control = on (0x030000, VGA compatible controller, i915)
/sys/bus/pci/devices/0000:00:04.0/power/control = on (0x118000, Signal processing controller, proc_thermal)
/sys/bus/pci/devices/0000:00:06.0/power/control = on (0x060400, PCI bridge, pcieport)
/sys/bus/pci/devices/0000:00:07.0/power/control = on (0x060400, PCI bridge, pcieport)
/sys/bus/pci/devices/0000:00:07.1/power/control = on (0x060400, PCI bridge, pcieport)
/sys/bus/pci/devices/0000:00:08.0/power/control = on (0x088000, System peripheral, no driver)
/sys/bus/pci/devices/0000:00:0a.0/power/control = on (0x118000, Signal processing controller, no driver)
/sys/bus/pci/devices/0000:00:0d.0/power/control = on (0x0c0330, USB controller, xhci_hcd)
/sys/bus/pci/devices/0000:00:0d.2/power/control = on (0x0c0340, USB controller, thunderbolt)
/sys/bus/pci/devices/0000:00:0e.0/power/control = on (0x010400, RAID bus controller, vmd)
/sys/bus/pci/devices/0000:00:12.0/power/control = on (0x070000, Serial controller, intel_ish_ipc)
/sys/bus/pci/devices/0000:00:14.0/power/control = on (0x0c0330, USB controller, xhci_hcd)
/sys/bus/pci/devices/0000:00:14.2/power/control = on (0x050000, RAM memory, no driver)
/sys/bus/pci/devices/0000:00:15.0/power/control = on (0x0c8000, Serial bus controller [0c80], intel-lpss)
/sys/bus/pci/devices/0000:00:15.1/power/control = on (0x0c8000, Serial bus controller [0c80], intel-lpss)
/sys/bus/pci/devices/0000:00:15.2/power/control = on (0x0c8000, Serial bus controller [0c80], intel-lpss)
/sys/bus/pci/devices/0000:00:15.3/power/control = on (0x0c8000, Serial bus controller [0c80], intel-lpss)
/sys/bus/pci/devices/0000:00:16.0/power/control = auto (0x078000, Communication controller, mei_me)
/sys/bus/pci/devices/0000:00:1c.0/power/control = on (0x060400, PCI bridge, pcieport)
/sys/bus/pci/devices/0000:00:1c.3/power/control = on (0x060400, PCI bridge, pcieport)
/sys/bus/pci/devices/0000:00:1d.0/power/control = on (0x088000, System peripheral, no driver)
/sys/bus/pci/devices/0000:00:1f.0/power/control = on (0x060100, ISA bridge, no driver)
/sys/bus/pci/devices/0000:00:1f.3/power/control = on (0x040100, Multimedia audio controller, sof-audio-pci-intel-tgl)
/sys/bus/pci/devices/0000:00:1f.4/power/control = on (0x0c0500, SMBus, i801_smbus)
/sys/bus/pci/devices/0000:00:1f.5/power/control = on (0x0c8000, Serial bus controller [0c80], no driver)
/sys/bus/pci/devices/0000:01:00.0/power/control = auto (0x030200, 3D controller, nouveau)
/sys/bus/pci/devices/0000:59:00.0/power/control = on (0x028000, Network controller, iwlwifi)
/sys/bus/pci/devices/0000:10000:e0:1d.0/power/control = (not available) (, PCI bridge, no driver)
/sys/bus/pci/devices/0000:10000:e1:00.0/power/control = (not available) (, Non-Volatile memory controller, no driver)
+++ USB
Autosuspend = enabled
Device allowlist = (not configured)
Device denylist = (not configured)
Exclude audio = enabled
Exclude bluetooth = disabled
Exclude phones = disabled
Exclude printers = enabled
Exclude WWAN = disabled
Bus 004 Device 001 ID 1d6b:0003 control = auto, autosuspend_delay_ms = 0 -- Linux Foundation 3.0 root hub (hub)
Bus 003 Device 004 ID 0bda:0129 control = auto, autosuspend_delay_ms = 2000 -- Realtek Semiconductor Corp. RTS5129 Card Reader Controller (rtsx_usb)
Bus 003 Device 003 ID 13d3:56eb control = auto, autosuspend_delay_ms = 2000 -- IMC Networks USB2.0 HD UVC WebCam (uvcvideo)
Bus 003 Device 005 ID 8087:0029 control = auto, autosuspend_delay_ms = 2000 -- Intel Corp. (btusb)
Bus 003 Device 002 ID 045e:0737 control = on, autosuspend_delay_ms = 2000 -- Microsoft Corp. Compact Optical Mouse 500 (usbhid)
Bus 003 Device 001 ID 1d6b:0002 control = auto, autosuspend_delay_ms = 0 -- Linux Foundation 2.0 root hub (hub)
Bus 002 Device 002 ID 056e:6035 control = on, autosuspend_delay_ms = 2000 -- Elecom Co., Ltd MF-CAU31 (usb-storage)
Bus 002 Device 001 ID 1d6b:0003 control = auto, autosuspend_delay_ms = 0 -- Linux Foundation 3.0 root hub (hub)
Bus 001 Device 001 ID 1d6b:0002 control = auto, autosuspend_delay_ms = 0 -- Linux Foundation 2.0 root hub (hub)
+++ Battery Care
Plugin: asus
Supported features: charge threshold
Driver usage:
* natacpi (asus_wmi) = active (charge threshold)
Parameter value range:
* STOP_CHARGE_THRESH_BAT0/1: 0(off)..100(default)
+++ Battery Status: BAT0
/sys/class/power_supply/BAT0/manufacturer = ASUSTeK
/sys/class/power_supply/BAT0/model_name = ASUS Battery
/sys/class/power_supply/BAT0/cycle_count = 16
/sys/class/power_supply/BAT0/energy_full_design = 70001 [mWh]
/sys/class/power_supply/BAT0/energy_full = 68329 [mWh]
/sys/class/power_supply/BAT0/energy_now = 54439 [mWh]
/sys/class/power_supply/BAT0/power_now = 0 [mW]
/sys/class/power_supply/BAT0/status = Not charging
/sys/class/power_supply/BAT0/charge_control_end_threshold = 80 [%]
Charge = 79.7 [%]
Capacity = 97.6 [%]
+++ Recommendations
* Install smartmontools for disk drive health info